SuperVidel drivers 2015-03-28
Updated August 19 2017
Contains an updated svscreen.sys for the PMMU-optimized drivers from 2014-03-01. Just replace svscreen.sys in GEMSYS. Read the included file readme.
Download

SuperVidel drivers 2014-03-01
Updated August 19 2017
Contains PMMU-optimized drivers for better performance. Read the readme-file for usage-instructions. Just replace the included files in your GEMSYS-folder(svscreen.sys), AUTO-folder(sv_xbios.prg) and root of your boot drive(SV.INF).
Download

SuperVidel firmware v010 with extra variants
Updated August 13 2016
Same functionality as the ordinary FW010 except these files have different timing scores in Xilinx ISE. Try these files if you experience problems with the ordinary FW010. Do not mix mcs_0 from one score with mcs_1 from another score! Score 2 here is the same as the ordinary FW010.
Download

SuperVidel Update with firmware v011 and extra files
Updated August 14 2016
Increased the superblitter FIFO from 512 longwords to 2048. Added a debug counter in a SV register. The extra variants of the MCS files have different timing scores. Try the lowest one first. If you experience problems with it, try the higher ones. Do not mix MCS_0 from one score with MCS_1 from another score!
Download

SuperVidel Memory Map
Updated July 13 2016
Describes all SuperVidel registers and where the graphics RAM lies.
Download

SVEthLANa MintNet driver v0.9 source files
Updated April 28 2016
For use with SV FW v10 or later.
Download

SuperVidel Firmware v010
Updated April 26 2016
Contains FW files rev 10. New feature(s) is DMA used for svethlana transfers to/from DDR2 RAM. Speedtests to remote server show speed increased from 70KB/s to 1.5MB/s. Requires new v0.9 Svethlana driver. Old Svethlana driver v0.1 will not work anymore. DDR clock is set to 200MHz (DDR400). You need a (Xilinx) USB JTAG programmer to update your SV with these files.
Download

SVEthLANa MintNet driver v0.9
Updated April 26 2016
Tested ONLY under Mint 1.17.0. Requires SuperVidel FW v010 or later. Gives greatly increased DL/UL speed.
Download

SuperVidel Update with firmware v010
Updated April 26 2016
A tool for updating the firmware of your SuperVidel. Tested under Mint 1.17.0 and TOS 4.04. Must be run in 060-mode. News i FW 010: Svethlana now uses DMA to DDR2, with 64 buffers in each direction.
Download

SuperVidel Update with firmware v009
Updated March 16 2016
A tool for updating the firmware of your SuperVidel. Tested under Mint 1.17.0 and TOS 4.04. Must be run in 060-mode. News i FW 009: Blitter FIFO.
Download

SuperVidel Firmware v009 DDR200MHz
Updated March 06 2016
Contains FW files rev 9. New feature(s) is a FIFO for queueing SuperBlitter registers. See SuperVidelMemoryMap.pdf for details. DDR clock is set to 200MHz (DDR400). You need a (Xilinx) USB JTAG programmer to update your SV with these files.
Download

SuperVidel Firmware v007 DDR210MHz
Updated November 24 2014
Contains experimental FW files for setting DDR clock to 210MHz (DDR420). This can only be tested if you have a (Xilinx) USB JTAG programmer. Test this file after testing the 200MHz one.
Download

SuperVidel Firmware v007 DDR200MHz
Updated November 24 2014
Contains experimental FW files for setting DDR clock to 200MHz (DDR400). This can only be tested if you have a (Xilinx) USB JTAG programmer. Test this file before testing the 210MHz one.
Download

SuperVidel Update with firmware v006
Updated December 28 2013
A tool for updating the firmware of your SuperVidel. Tested under Mint 1.17.0 and TOS 4.04. Must be run in 060-mode. News i FW 006: Optimimized CT60 clock from 75 to 85MHz. Register bit for triggering Blitter done interrupt.
Download

SuperVidel firmware v005
Updated August 27 2013
SV firmware in MCS-format. For use with Xilinx Impact (WinXP or later or Ubuntu), when you have bricked your SV and cannot use SVUPDxxx.APP. Follow the instructions manual for updating the ABE+SDR, but instead use the 2mm-pitch 14-pin flat cable that comes with the Xilinx Platform Cable USB to connect to the SV (connector JP2 near the DVI). Note the key on the cable! And be careful with the chips on the bottom side of the SV while you press to insert the cable! The "..._1.mcs" should be selected for the left icon in Impact and the "..._0.mcs" should be selected for the right icon.
Download

SuperVidel drivers
Updated March 05 2014
Contains the NVDI SYS-files and SV_XBIOS.PRG for the AUTO-folder. Please refer to the installation manual for instructions.
Download

HW VHDL SW overview
Updated March 12 2012
A schematic overview of the SuperVidel hardware and its VHDL code structure, as well as a short description of available software tools and drivers, both Atari and PC.
Download

SuperVidel installation manual
Updated August 19 2013
Describes how to install the SuperVidel in various cases. Revision 5.
Download

SVEthLANa MintNet driver v0.1
Updated January 08 2011
Tested under Mint 1.17.0. Works only on SV FW before v010.
Download

NATCAR demo
Updated July 25 2016
Our first SuperVidel game! :) It is a Supercars inspired racing game for 1, 2 or 4 players (split screen). You can use joysticks, Jaguar gamepads and keyboard for controlling the cars. There are currently 7 tracks in the championship.
Download

NatFrame v1.1b
Updated January 01 1970
NatFrame driver for Magic 5.x and later. This zip-file now includes the necessary SAVE_PAL.PRG too.
Download

EtherNat MiNTNet driver v0.1
Updated January 01 1970
EtherNat MiNTNet driver v0.1 including source code.
Download

EtherNat JED-file
Updated August 21 2015
From Dec 10th 2010 for the CPLD firmware, that fixes the floodping bug and attempts better compatibility with the CTPCI.
Download