2010-02-20 19:38:58
We have just successfully repaired Torbjörn's CT60! :) After replacing the ABE chip the 060 mode didn't boot, so we spent a few days measuring the bus signals. But what made the CT60 boot at last was that we did some additional soldering on the back och left side of the ABE. Apparently when you keep removing and inserting the CT60 some ABE pin solders develop cracks when the PCB is bent and eventually the CT60 won't boot. We now believe this is the problem with Henrik's CT60 too. Finally at last we can try out our Videl compatibility code in the Super videl...

2010-01-31 15:40:04
Forgot to mention below that the Videl register settings for the VGA resolutions that we tested in simulation were taken using Screenspain after having set a resolution from the desktop. So we're testing the actual TOS settings, not our own made up resolutions. This means we should see Videl screen output being mirrored on the SV output when starting the falcon in for example VGA 640x480 16 colors.

2010-01-31 15:30:43
In simulation we have now verified that a VGA 640x480 16-color resolution and a VGA 320x240 16-bit one are correctly translated into SuperVidel register settings, so we get the correct VGA timing and data output. We have also run the VHDL design through the Xilinx ISE synthesis and place-and-route, and we now have the mcs-file necessary for testing the Videl translation on the SuperVidel in reality.

The problem now is that my (Torbjörn) CT60 is under repair since its motherboard connectors as well as the ABE chip were broken. And now Henrik's CT60 is also making trouble, because of bad motherboard connectors. Those connectors seem to wear out too easily when we remove and replace the CT60 on the motherboard. Henrik is now replacing the connectors with our own CT60-extender boards, to make the CT60+SV fit in the standard Falcon case.

After that we can test the Videl translation.

2010-01-24 20:49:41
We have figured out the crashes in the Xilinx ISE Simulator at last, and have also made some progress on the actual Videl register translation. Now we get correct VGA hsync and vsync timing in simulation. Just some minor details to fix before we can test the Videl compatiblity in reality.

2010-01-16 20:03:37
After a bit of in-depth Videl register researching, we have implemented a Videl-to-SuperVidel-registers translation block in our VHDL code. We're following Mikro's Videl guide and just like Mikro says, the horizontal timing registers are the most complicated to get right. We're currently simulating our code and Xilinx ISE Simulator has given us some strange crashes to figure out, which of course follow no logic. But at least we're on the right track.

2009-12-15 13:45:17
We have begun adding the Videl registers to our VHDL code of the SuperVidel. The purpose of these registers is to snoop all writes going to the old Videl registers, so that we may interpret what was written and set our SuperVidel registers so that we get the same resolution as the Videl would have produced. That's the main purpose of this entire project. :)
The heavy part of these registers is the interpretation though, not the registers themselves.

We've also been thinking a bit more about the Videl compatibility. During discussions with Peter Persson we realized that the Timer-B of the MFP-chip wouldn't work with our current SuperVidel construction. For this to work we have to feed the video clock of the old Videl into the SuperVidel and let the old Videl work as before. This way you'll get the old Videl picture out through the SuperVidel, as well as the Timer-B HBL-interrupts from the MFP correctly synchronized. In order to feed the old Videl clock into the SuperVidel, a wire will have to be soldered from the old Videl chip. Note that soldering this wire isn't a requirement for getting the SuperVidel to work, but without it the Timer-B won't work correctly in old games and demos. And it's only near the Videl chip that you'll have to solder. The other end of this wire goes to a small 1.27mm connector on the SuperVidel, for easy detachment.

/Henrik